• 대전광역시 유성구 대덕대로 582
  • 504호 (도룡동, 옥토빌딩)
  • 전화번호 042)825-6820 팩스 : 042)825-6839

일반산업

Analog Telemetry - WDC

Clamp On (9300 & 1600)
* 9300
* Model 9300 Clamp-on Rotary Torque Transducer System, Converts Shaft into a Torque Transducer


* 제품상세보기

The Series 9300 Torsionometer is ideal for measuring torque on machinery where little down time can be afforded. The quick installation of the clamp-on collars with the pre-calibrated bending beam converts I/O shafts into instant torque transducers. The 9300 Series are ideal for those applications involving repetitive testing of identical systems. The clamp-on 9300 Series uses a pre-calibrated bending beam which is clamped at each end by a counterbalanced collar around a heavy-wall or solid shaft to sense torque. Each installation uses one of a selection of bending beam lengths to generate the specific output to the on-board RF transmitter. The strain gage output is then coupled to the readout device or control loop via an RF telemetry package. A variety of collars and bending beams are available to accommodate high torque ranges and shafts from 2.5 in to 15.4 in diameter. Running speeds are from 2,500 RPM down to zero RPM. The built-in transmitter can be environmentally sealed for harsh environments and high vibration.

첨부 파일 :

Clamp On (9300 & 1600)
* 1602A
Model 1602A Clamp-On Propulsion Monitoring Systems, Converts Shaft into a Torque Transducer ( gives rpm and horsepower as well )


* 제품상세보기

The 1602A propulsion monitoring system fits shafts sized from 381 mm to 762 mm [15 in to 30 in] in diameter. The system is enclosed in a strong outer cover and has an electronics readout assembly in a water tight enclosure. These units together provide the means for measuring shaft torque and RPM. Digital readouts are available to display torque, RPM and computed horsepower. Built-in calibration check circuitry can be activated at any time to verify that all local displays and outputs are functional. Enhanced stability and reduced maintenance are the payback for selecting this system. The model 1602A/01 systems can be used in a variety of potential applications including fuel conservation programs, hull and propeller fouling, load and balancing on twin screw vessels, power plant monitors and sea trial torsion meters.

첨부 파일 :

Clamp On (9300 & 1600)
* 1602A-01
Model 1602A-01 Clamp-On Propulsion Monitoring Systems, Converts Shaft into a Torque Transducer


* 제품상세보기

The 1602A propulsion monitoring system fits shafts sized from 381 mm to 762 mm [15 in to 30 in] in diameter. The system is enclosed in a strong outer cover and has an electronics readout assembly in a water tight enclosure. These units together provide the means for measuring shaft torque and RPM. Digital readouts are available to display torque, RPM and computed horsepower. Built-in calibration check circuitry can be activated at any time to verify that all local displays and outputs are functional. Enhanced stability and reduced maintenance are the payback for selecting this system. The model 1602A/01 systems can be used in a variety of potential applications including fuel conservation programs, hull and propeller fouling, load and balancing on twin screw vessels, power plant monitors and sea trial torsion meters.

첨부 파일 :

Clamp On (9300 & 1600) 1603A
* 1603A
Model 1603A Clamp-On Propulsion Monitoring Systems (without cover), Converts Shaft into a Torque Transducer ( gives rpm and horsepower as well )


* 제품상세보기

The model 1603A and 1603A-01 power measurement system is identical to the model 1602A system except for the elimination of the cover over the shaft sensor unit which enables installation in tight spaces such as under existing covers or deck plates. The system fits shaft sizes from 63,5 mm to 391 mm [2.5 in to 15.4 in] in diameter. The system has an electronics readout assembly in a water tight enclosure. These units together provide means for measuring shaft torque and RPM. Digital readouts are available to display torque, RPM and computed horsepower. Built-in calibration check circuitry can be activated at any time to verify that all local displays and outputs are functional. Enhanced stability and reduced maintenance are the payback for selecting this system. The model 1603A and 1603A-01 systems can be used in a variety of potential applications including fuel conservation programs, hull and propeller fouling, power plant monitors and sea trial torsion meters.

첨부 파일 :

Clamp On (9300 & 1600) 1603A-01
* 1603A-01
Model 1603A-01 Clamp-On Propulsion Monitoring Systems (without cover), Converts Shaft into a Torque Transducer (Measures Torque only)


* 제품상세보기

The model 1603A and 1603A-01 power measurement system is identical to the model 1602A system except for the elimination of the cover over the shaft sensor unit which enables installation in tight spaces such as under existing covers or deck plates. The system fits shaft sizes from 63,5 mm to 391 mm [2.5 in to 15.4 in] in diameter. The system has an electronics readout assembly in a water tight enclosure. These units together provide means for measuring shaft torque and RPM. Digital readouts are available to display torque, RPM and computed horsepower. Built-in calibration check circuitry can be activated at any time to verify that all local displays and outputs are functional. Enhanced stability and reduced maintenance are the payback for selecting this system. The model 1603A and 1603A-01 systems can be used in a variety of potential applications including fuel conservation programs, hull and propeller fouling, power plant monitors and sea trial torsion meters.

첨부 파일 :

Clamp On (9300 & 1600) 1605A
* 1605A
Model 1605A Clamp-On Horsepower Monitoring System, Shaft Sizes From 381 mm to 762 mm [15 in to 30 in]


* 제품상세보기

The Model 1605A universal power and torque measurement system consists of bolt-on shaft sensor units for shafts between 381 mm and 762 mm [15 in and 30 in], which can handle most diesel and turbine power plants. Most ranges of RPM and power are accommodated with large over range capability. The data band width is dc to 1000 Hz, allowing for torsional vibration measurement without a second monitoring system.

첨부 파일 :

Rotary Measurement System 2101
* 2101
Model 2101 Rotary Measurement System, 1 Channel System, Induced Power, No Batteries Required, Wireless Telemetry. Optional 12 or 24 VDC supply versions are available.


* 제품상세보기

The 2100 series rotary torque measurement systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements. Utilizing an existing customer gage shaft assembly, the Honeywell Model 2100 Series Rotary Torque Measurement System takes the strain data from a rotating bridge assembly and converts it to a high level output via wireless telemetry. A combination of up to six transmitters and receivers operating on different frequencies will provide up to six points of measurement on the same shaft. Please contact the factory if more than six points of measurement are required. A scalable analog output and numeric display readout on the receiver provides an electrical and visual indication of the measurement. The receiver provides controls for gain and zero adjustments, display scaling, and IPS power setting.

첨부 파일 :

Rotary Measurement System 2102-WDC
* 2102-WDC
Model 2102-WDC Rotary Measurement System, 2 Channel System, Induced Power, No Batteries Required, Wireless Telemetry. Optional 12 or 24 VDC supply versions are available.


* 제품상세보기

The 2100 series rotary torque measurement systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements. Utilizing an existing customer gage shaft assembly, the Honeywell Model 2100 Series Rotary Torque Measurement System takes the strain data from a rotating bridge assembly and converts it to a high level output via wireless telemetry. A combination of up to six transmitters and receivers operating on different frequencies will provide up to six points of measurement on the same shaft. Please contact the factory if more than six points of measurement are required. A scalable analog output and numeric display readout on the receiver provides an electrical and visual indication of the measurement. The receiver provides controls for gain and zero adjustments, display scaling, and IPS power setting.

첨부 파일 :

Rotary Measurement System 2103
* 2103
Model 2103 Rotary Measurement System, 3 Channel System, Induced Power, No Batteries Required, Wireless Telemetry. Optional 12 or 24 VDC supply versions are available.


* 제품상세보기

The 2100 series rotary torque measurement systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements. Utilizing an existing customer gage shaft assembly, the Honeywell Model 2100 Series Rotary Torque Measurement System takes the strain data from a rotating bridge assembly and converts it to a high level output via wireless telemetry. A combination of up to six transmitters and receivers operating on different frequencies will provide up to six points of measurement on the same shaft. Please contact the factory if more than six points of measurement are required. A scalable analog output and numeric display readout on the receiver provides an electrical and visual indication of the measurement. The receiver provides controls for gain and zero adjustments, display scaling, and IPS power setting.

첨부 파일 :

Rotary Measurement System 2104
* 2104
Model 2104 Rotary Measurement System, 4 Channel System, Induced Power, No Batteries Required, Wireless Telemetry. Optional 12 or 24 VDC supply versions are available.


* 제품상세보기

The 2100 series rotary torque measurement systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements. Utilizing an existing customer gage shaft assembly, the Honeywell Model 2100 Series Rotary Torque Measurement System takes the strain data from a rotating bridge assembly and converts it to a high level output via wireless telemetry. A combination of up to six transmitters and receivers operating on different frequencies will provide up to six points of measurement on the same shaft. Please contact the factory if more than six points of measurement are required. A scalable analog output and numeric display readout on the receiver provides an electrical and visual indication of the measurement. The receiver provides controls for gain and zero adjustments, display scaling, and IPS power setting.

첨부 파일 :

Rotary Measurement System 2105-WDC
* 2105-WDC
Model 2105-WDC Rotary Measurement System, 5 Channel System, Induced Power, No Batteries Required, Wireless Telemetry. Optional 12 or 24 VDC supply versions are available.


* 제품상세보기

The 2100 series rotary torque measurement systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements. Utilizing an existing customer gage shaft assembly, the Honeywell Model 2100 Series Rotary Torque Measurement System takes the strain data from a rotating bridge assembly and converts it to a high level output via wireless telemetry. A combination of up to six transmitters and receivers operating on different frequencies will provide up to six points of measurement on the same shaft. Please contact the factory if more than six points of measurement are required. A scalable analog output and numeric display readout on the receiver provides an electrical and visual indication of the measurement. The receiver provides controls for gain and zero adjustments, display scaling, and IPS power setting.

Rotary Measurement System 2106
* 2106
Model 2106 Rotary Measurement System, 6 Channel System, Induced Power, No Batteries Required, Wireless Telemetry. Optional 12 or 24 VDC supply versions are available.


* 제품상세보기

The 2100 series rotary torque measurement systems are often well suited for both short and long term testing and monitoring of torque or strain on rotating applications where other measurement methods are affected by vibration, dust, moisture, high RPMs, and large axial/radial shaft movements. Utilizing an existing customer gage shaft assembly, the Honeywell Model 2100 Series Rotary Torque Measurement System takes the strain data from a rotating bridge assembly and converts it to a high level output via wireless telemetry. A combination of up to six transmitters and receivers operating on different frequencies will provide up to six points of measurement on the same shaft. Please contact the factory if more than six points of measurement are required. A scalable analog output and numeric display readout on the receiver provides an electrical and visual indication of the measurement. The receiver provides controls for gain and zero adjustments, display scaling, and IPS power setting.

첨부 파일 :

Rotary Measurement System 1202B
* 1202B
Model 1202B Rotary Torque / RPM/HP Measurement System, Three Analog Outputs and Optional Isolated Output Channel


* 제품상세보기

Model 1202B is a wireless telemetry system capable of monitoring the parameters of torque, RPM, and horsepower utilizing a 1226A collar assembly, 2120B transmitter, stationary loop antenna, 1211D power seperation unit, and 1642A receiver unit.

첨부 파일 :

Rotary Measurement System 1205B
* 1205B
Model 1205B Rotary Torque / RPM/HP Measurement System, Three Analog Outputs and Optional Isolated Output Channel


* 제품상세보기

Model 1205B is a wireless telemetry system capable of monitoring the parameters of torque, RPM, and horsepower utilizing a 1226A collar assembly, 2120B transmitter, stationary loop antenna, 1211D power seperation unit, and 1642A receiver unit.

첨부 파일 :